Difference between revisions of "Bering-uClibc 5.x - Developer Guide - Appendices - Hardware-Specific Guides"

From bering-uClibc
Jump to: navigation, search
(Linux Kernel Source remove raspberry pi foundation git hub mention buildtool.org)
(initramfs initrd initmod)
Line 54: Line 54:
 
  CONFIG_SMC91X=y
 
  CONFIG_SMC91X=y
  
There does not seem to be any standard provision for loading an initramfs (initrd) file when booting the Raspberry Pi.
+
===Considerations about initrd===
That means we need to embed the [[Bering-uClibc 5.x]] initrd into the kernel using the <tt>CONFIG_INITRAMFS_SOURCE</tt> configuration variable.
+
We use initrd.lrp, providing the basic stuff to boot, and initmod.lrp with architecture specfic modules.
 +
 +
While the bootloader of Raspberry Pi supports loading an initramfs (initrd) file when booting it fails to load more than one initrd files (initrd and initmod) as other hardware does.
  
:[[User:Davidmbrooke|Davidmbrooke]] 10:50, 1 July 2012 (UTC): Actually that's not (or no longer) the case: <code class="filename">config.txt</code> can contain an entry like the following:
+
So we first have to concatenate the two files into one.
:<pre>ramfsfile=initrd.cpio</pre>
+
This is done with the following commands:
:as described at [http://elinux.org/RPi_config.txt#Boot_options the eLinux Wiki].
+
mv initrd.lrp initrd.gz
::[[User:Davidmbrooke|Davidmbrooke]] 19:20, 3 July 2012 (UTC) But I can't get it to work :-(
+
mv initmod.lrp initmod.gz
 +
cat initrd.gz initmod.gz > initrd-rpi.gz
 +
mv initrd-rpi.gz initrd-rpi.lrp
 +
 
 +
The file <code class="filename">initrd-rpi.lrp</code> then needs to declared in <code class="filename">config.txt</code>  
 +
as described at [http://elinux.org/RPi_config.txt#Boot_options the eLinux Wiki].
 +
 
 +
initramfs initrd-rpi.lrp 0x00800000
  
 
===Boot Disk Layout===
 
===Boot Disk Layout===

Revision as of 15:00, 1 April 2013

Hardware-Specific Guides
Prev Bering-uClibc 5.x - Developer Guide Next

Introduction

This page provides guidelines for Bering-uClibc 5.x developers targeting specific hardware devices.

See also the equivalent page in the User Guide for hardware-specific information relevant to Users as well as Developers.


ARM CPU Architecture

Raspberry Pi Model B

Overview

The Raspberry Pi Model B has a Broadcom BCM2835 "system on a chip" integrated circuit containing an ARM1176JZF-S CPU which implements the ARMv6 CPU architecture standard.

  • As described here, the ARM1176JZF-S is an ARM1176JZ-S with the addition of a Vector Floating-Point (VFP) coprocessor. This means it can execute floating-point arithmetic in hardware rather than (only) in software.

A PDF data sheet for the BCM2835 can be downloaded from here. The BCM2835 contains a variety of devices and many of these seem to be identified with the string BCM2708 rather than BCM2835, judging by the example boot log from an Alpha board here

There is no Real-Time Clock so it is necessary to use an NTP or similar time source for accurate time keeping.

There is a USB interface (with 2 Type-A sockets) and also a 10/100 Ethernet interface, connected internally via the USB bus.

While there is no standard physical connector for an RS-232 serial interface, the GPIO header does support serial communications using 3.3V TTL signals. Something like a PL2303 adaptor can be used to convert these to USB for connection to a host computer running a terminal emulator.

Linux Kernel Source

Many of the device drivers for the on-board peripherals are not currently (April 2013) included in the mainstream Linux source tree.

Developers of buildroot provides one big patch with all changes for Raspberry Pi, based on the work of the Raspberry Pi foundation, for the Linux Kernel 3.6.11. See Lightweight Raspberry Pi Distribution Git Hub based on Buildroot

We've started our work towards a LEAF image for Raspberry Pi on this repository. Note that the kernel version differs from our mainline version currently in development (3.4.x).

Linux Kernel Configuration

SD Card Driver

Based on this post the relevant device drivers for the SD card interface are:

CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_BCM2708=y
CONFIG_MMC_SDHCI_BCM2708_DMA=y
# CONFIG_MMC_BCM2708 is not set

USB Driver

The USB interface driver is the DWC OTG Controller:

CONFIG_USB_DWCOTG=y

Ethernet Driver

The Ethernet interface chip is an SMC 91X-compatible device:

CONFIG_NET_VENDOR_SMSC=y
CONFIG_SMC91X=y

Considerations about initrd

We use initrd.lrp, providing the basic stuff to boot, and initmod.lrp with architecture specfic modules.

While the bootloader of Raspberry Pi supports loading an initramfs (initrd) file when booting it fails to load more than one initrd files (initrd and initmod) as other hardware does.

So we first have to concatenate the two files into one. This is done with the following commands:

mv initrd.lrp initrd.gz
mv initmod.lrp initmod.gz
cat initrd.gz initmod.gz > initrd-rpi.gz
mv initrd-rpi.gz initrd-rpi.lrp

The file initrd-rpi.lrp then needs to declared in config.txt as described at the eLinux Wiki.

initramfs initrd-rpi.lrp 0x00800000 

Boot Disk Layout

The Raspberry Pi must boot from its SD card and some vital files must be present in the root directory of the boot partition.

The latest versions of these files can be downloaded from the raspberrypi/firmware page on GitHub.

The first disk partition on the SD card must be formatted as a VFAT filesystem. It works OK if the partition type is 0xb (W95 FAT32). This partition does not have to to be marked as "bootable".

The boot sequence is as follows (based on content here):

  1. The first-stage bootloader, built into the very small on-chip ROM runs, and loads...
  2. A file called bootcode.bin which contains the second-stage bootloader. This runs, and loads...
  3. A file called loader.bin which contains the third-stage bootloader. This understands the ELF file format and loads...
  4. A file called start.elf which contains the GPU binary driver code. If the optional configuration file config.txt is present this is read and processed.
    • The syntax for config.txt is comprehensively documented at the eLinux Wiki.
    • By default start.elf loads a file called kernel.img, passing it the command line specified in file cmdline.txt
    • The default name kernel.img can be overriden by an entry like the following in config.txt
      kernel=u-boot.bin
    • Rather than having a separate cmdline.txt the kernel command line can also be specified by an entry like the following in config.txt
      cmdline=LEAFCFG=/dev/mmcblk0p1:vfat
  5. The file kernel.img is typically a standard uncompressed Linux kernel Image file
    • Old versions of the Raspberry Pi firmware demanded a special prefix to be added to the kernel file. As of June 2012 this is no longer the case.

Note that the Raspberry Pi references the first disk partition as /dev/mmcblk0p1 and the second disk partition as /dev/mmcblk0p2.



Prev Up Next