View source for Bering-uClibc 6.x - User Guide - Advanced Topics - Setting Up a Home Automation controller with heyu

{| summary="Navigation header" width="100%"
! colspan="3" align="center" | [[Bering-uClibc 6.x - User Guide - Advanced Topics - Setting Up a Home Automation controller with heyu |Advanced Topics - Setting Up a Home Automation Controller with heyu]]
|-
| width="20%" align="left"   | [[Bering-uClibc 6.x - User Guide - Advanced Topics - Setting Up a HTTP Anti Virus Proxy|Prev]]
! width="60%" align="center" | [[Bering-uClibc 6.x - User Guide]]
| width="20%" align="right"  | [[Bering-uClibc 6.x - User Guide - Advanced Topics - Setting Up Ad blocking with dnsmasq|Next]]
|}
----

==Objectives==

This page explains how to turn a LEAF Bering-uClibc router into a Home Automation controller using the <code class="filename">heyu.lrp</code> Package. Taken from http://www.heyu.com introduction: "Heyu is a text-based console program for remotely controlling lights and appliances in the home or office. The complete source is made available under the GNU GPLv3 license. Heyu uses the CM11A computer interface to send and receive X10 control signals over the AC power lines to modules which can turn On, Off, or Dim attached lamps or appliances. It can store a schedule of timed events in the CM11A memory for execution without any more computer intervention." It is also mentioned that " Heyu supports an optional W800RF32A, MR26A, or RFXCOM RF receiver connected to a second port as an auxiliary input device for RF signals from X10 and other supported transmitters. Heyu can also use an optional CM17A interface to transmit X10 RF signals." Though what follows has only been tested on the CM11A computer interface.

==Prerequisites==
The prerequisites are: 
* a working LEAF Bering-uClibc 6.x router.
* a CM11A Computer interface module, some might still be available on line.
Unfortunately CM11 or CM12 interface modules, as they are called in Europe, are not as easy to find as the north American CM11a. There might be some at [http://www.elektroshop.nl/?subcats=Y&status=A&pshort=Y&pfull=Y&pname=Y&pkeywords=Y&search_performed=Y&q=cm11&dispatch=products.search Elektroshop], or at [http://www.uk-automation.co.uk/products/X10-Computer-Interface-Serial-CM11-or-CM12.html uk-automation].
* a few X10 appliance or lamp modules.
* a serial port on your router, Heyu uses by default ttyS0.
* the <code class="filename">heyu.lrp</code> Package.

==Configure the System==

===Loading the Package===
Load the heyu.lrp Package by adding heyu to the list of Packages specified in the leaf.cfg file on the boot media. There are no dependencies for this Package.

===Configuration files=== 
To start and test heyu.lrp the default configuration files /etc/heyu/x10.conf and /etc/heyu/x10.sched should work.

===Test your setup===
At this point you can either reboot the firewall or install <code class ="filename">heyu.lrp</code> manually by: 

 mount /dev/sdx1 /mnt   # x= default to a, but could be b, c, etc, if you have other disks 
 cd /mnt 
 apkg -i heyu 
 heyu

You should see something like: 

 Heyu version 2.11-rc1 
 X10 Automation for Linux, Unix, and Mac OS X 
 Copyright Charles W. Sullivan and Daniel B. Suthers 
 Usage: heyu [options] <command>  (Enter 'heyu help' for commands.) 

Then type: 
 heyu start 
  

And check that task heyu_relay is displayed 
 ps
 11236 root      1432 S    heyu_relay

Get more info:
 heyu info 

 Heyu version 2.11-rc1 
 Configuration at //etc/heyu/x10.conf 
 Powerline interface on /dev/ttyS0 
 Firmware revision Level = 1 
 Interface battery usage = Unknown 
 Raw interface clock: Tue, Day 076, 00:51:55 
 (--> Civil Time: Tue 18 Mar 2014   00:51:55 UTC) 
 No schedule has been uploaded by Heyu. 
 Housecode = K
 0 = off, 1 = on,               unit  16.......8...4..1 
 Last addressed device =       0x0400 (0000000000001000) 
 Status of monitored devices = 0x0000 (0000000000000000) 
 Status of dimmed devices =    0x0000 (0000000000000000)

Now send a command to an appliance module, with address "k 5" for instance, where "k" is the housecode set in the configuration. 

 heyu on k5 
 heyu off k5 

If you hear two heart warming thumbs, everything works fine... have fun !

===Troubleshooting===

Check again that heyu_relay is working.

Check serial port ttyS0 parameters: 

 stty -F /dev/ttyS0        # the speed should be 4800 bauds. 

Check the CM11A is transmitting by typing: 

 cat /dev/ttyS0 

The CM11a will transmit the letter “z” when it detects a module changing state.
Plug a lamp in one of your connected module and force it to activate by switching the lamp on or off a few time you should then see the letter "z" appears every seconds on your display.
You also can use an RF remote control, if you have one, to activate any module.

==Additional reading==

The net is crowded with x10 howtos, here are a few interesting links:
* [http://www.heyu.org/ heyu.org]
* [http://www.idobartana.com/hakb/index.htm idobartana] This site stores comprehensive information on home automation based on X-10.
* [http://www.hansotten.com/attersjo/index.html hansotten] A page created in order to publish some info about home automation stuff and especially on how to use X10 equipment on 220V-50Hz. 
* [https://play.google.com/store/apps/details?id=com.melloware.x10.android&hl=en X10 Android App]
* [http://docs.domogik.org/domogik/0.1/en/plugins/x10_heyu/index.html domogik ]
* [http://lea-linux.org/documentations/Le_X10_et_Linux lea-linux] (french website)
----
{| summary="Navigation footer" width="100%"
| width="40%" align="left"   | [[Bering-uClibc 6.x - User Guide - Advanced Topics - Setting Up a HTTP Anti Virus Proxy|Prev]]
| width="20%" align="center" | [[Bering-uClibc 6.x - User Guide - Advanced Topics|Up]]
| width="40%" align="right"  | [[Bering-uClibc 6.x - User Guide - Advanced Topics - Setting Up Ad blocking with dnsmasq|Next]]
|}

[[Category:Bering-uClibc 6.x]]
[[Category:User Guide]]